Constructions, Loci and Bearings

Constructions, Loci and Bearings Flashcards

Spec G2 · AQA GCSE Maths: Flashcards

Studying this course? Keep your progress in one place.

Flip each card. Be honest: the ones you mark Not yet come back first.

15 cards

Tap a card to flip it. Swipe right if you knew it, left if not.

See all 15 cards
What is a perpendicular bisector and how do you construct it using a ruler and compass?
A perpendicular bisector is a line that passes through the midpoint of a line segment at right angles to it. To construct: (1) Open compass to more than half the line segment's length, (2) Draw arcs from both endpoints on either side of the line, (3) Join the two intersection points of the arcs with a ruler. This line is the perpendicular bisector.
Describe the method to construct an angle bisector using ruler and compass.
To construct an angle bisector: (1) Place compass point at the angle's vertex and draw an arc crossing both rays of the angle, (2) From each intersection point on the rays, draw two arcs of equal radius that intersect between the rays, (3) Draw a straight line from the vertex through the intersection point of these arcs. This line bisects the angle.
What is the standard method for constructing a triangle given three sides (SSS)?
To construct a triangle with three known sides: (1) Draw the longest side as the base using a ruler, (2) Set compass to the length of the second side and draw an arc from one endpoint, (3) Set compass to the length of the third side and draw an arc from the other endpoint, (4) Mark the intersection point of the arcs, (5) Join this point to both endpoints to complete the triangle.
Define a locus and give an example of a common locus.
A locus is the set of all points that satisfy a given condition or rule. Common examples include: the perpendicular bisector of a line segment (all points equidistant from two fixed points), a circle (all points at a fixed distance from a centre point), and angle bisectors (all points equidistant from two lines).
What does it mean to apply loci to solve a problem involving combined conditions?
This means finding the region that satisfies two or more locus conditions simultaneously. For example, finding all points that are both within a certain distance of a point AND on one side of a line. The solution is the intersection or overlap of the regions defined by each individual locus.
What is a three-figure bearing?
A three-figure bearing is a direction measured clockwise from North, written as a three-digit number from 000° to 360°. For example, 090° is due East, 180° is due South, and 270° is due West. North is always 000° (or 360°).
How do you convert a compass direction (such as SW) to a three-figure bearing?
South-West is 225° (180° + 45°). To convert: North = 000°, East = 090°, South = 180°, West = 270°. Intermediate directions like NE = 045°, SE = 135°, SW = 225°, NW = 315°. Always measure clockwise from North.
What is a scale factor in a scale drawing?
A scale factor is the ratio between a distance on a scale drawing and the corresponding actual distance in real life. For example, a scale factor of 1:100 means 1 unit on the drawing represents 100 units in reality. Scale factors can also be written as fractions or ratios like 1/50.
If a scale drawing has a scale of 1:50 and a length measures 4 cm on the drawing, what is the actual length?
Actual length = 4 cm × 50 = 200 cm = 2 metres. Multiply the measurement on the drawing by the scale factor to find the real-life measurement.
How do you find the scale factor if you know a real measurement and its corresponding measurement on a scale drawing?
Scale factor = Real measurement ÷ Drawing measurement. For example, if 5 cm on a drawing represents 250 cm in reality, the scale factor is 250 ÷ 5 = 50, or written as 1:50.
Explain how to use scale drawings and bearings together in a problem.
Start by drawing a diagram using the scale given. Mark the first position, then use the three-figure bearing to draw a line in the correct direction from North. Measure the appropriate distance according to the scale, plot the second position, and use a protractor or compass to verify bearings. Actual distances are found by multiplying scaled measurements by the scale factor.
What is the locus of all points that are a fixed distance from a given point?
A circle with the given point as its centre and the fixed distance as its radius. All points on this circle are equidistant from the centre point.
What is the locus of all points equidistant from two fixed points?
The perpendicular bisector of the line segment joining the two fixed points. Every point on this line is the same distance from both fixed points.
What is the locus of all points equidistant from two lines?
The angle bisector(s) of the angle formed by the two lines. All points on the angle bisector are the same perpendicular distance from both lines.
How do you construct a triangle given two sides and the included angle (SAS)?
To construct a triangle with two known sides and the included angle: (1) Draw one side using a ruler, (2) Use a protractor to mark the required angle at one endpoint, (3) Draw the second side along the angle line to the correct length, (4) Join the two endpoints to complete the triangle.

Flashcards