1.6 Approximation and error
Studying this course? Keep your progress in one place.
Key facts
- Round to decimal places by counting after the point, and to significant figures from the first non-zero digit.
- A value rounded to a given accuracy lies within half a unit of its last digit: (1 d.p.) means .
- Percentage error , dividing by the exact value.
- Keep full calculator values and round only the final answer, to 3 s.f. unless told otherwise.
- Estimate with 1 s.f. values to check that an answer is reasonable.
Decimal places and significant figures
Count decimal places after the point, but count significant figures from the first non-zero digit; then round up if the next digit is 5 or more.
To round to decimal places (d.p.), count digits after the decimal point. To round to significant figures (s.f.), count from the first non-zero digit. Look at the next digit: or more rounds up.
In IB exams, give exact values or 3 s.f. (money to 2 d.p.) unless told otherwise.
Decimal places
- Count after the decimal point
- (3 d.p.)
- Leading zeros count
Significant figures
- Count from the first non-zero digit
- (2 s.f.)
- Leading zeros do not count
Worked example
Round to 2 s.f. and to 3 d.p.
- 1
2 s.f.: the first non-zero digit is , so keep and . The next digit is , so round up: .
- 2
3 d.p.: keep . The next digit is , so round up: .
What is rounded to 2 significant figures?
Upper and lower bounds
A rounded value lies within half a unit of its last digit, so the lower bound is included and the upper bound is not.
If to one decimal place, then . The lower bound is included; the upper bound is not, because would round up to .
Other examples: m to the nearest metre gives .
For a calculation, combine bounds sensibly. For an area, the lower bound uses both lower bounds and the upper bound uses both upper bounds.
Worked example
A rectangle is m by m, each to the nearest metre. Find the bounds of its area.
- 1
Lower bound: .
- 2
Upper bound: .
A mass is kg to 1 d.p. What is its upper bound?
Percentage error
Percentage error is the difference between approximate and exact values, divided by the exact value, as a percentage.
The percentage error compares an approximate value with the exact value . Errors arise from rounding (a value to 1 d.p. can be wrong by up to ) and from measurement limits, such as a ruler marked in mm.
The greatest possible error in a rounded value is half a unit of its last digit. For cm that is cm, or .
- Percentage error
Worked example
The radius of a circle is measured as cm but is really cm. Find the percentage error in the area.
- 1
Approximate area:
- 2
Exact area:
- 3
The exact length is m and the approximate length is m. What is the percentage error?
Estimation and sense checks
Round each number to 1 s.f. and calculate by hand; if the GDC answer is far from your estimate, look for a slip.
Estimating means rounding each number to 1 significant figure. For : , so is reasonable but or is not.
Check context too: a length cannot be negative, a probability lies between and , and an answer should not use more accuracy than the data. A result from (3 s.f.) and (2 s.f.) is given to 2 s.f.: .
- 1
Round
each value to 1 s.f.
- 2
Calculate
the estimate by hand
- 3
Compare
with the GDC answer
- 4
Check context
sign, size and units
Estimate by rounding to 1 s.f.
Try an exam question
A rectangular plot has length m and width m, each measured to the nearest metre. (a) Find the upper bound of the area. (b) The area is calculated as m. Find the percentage error if the true area is the upper bound.
[4 marks]
- [1]Uses the upper bounds and .
- [1]Upper bound of area m.
- [1]Percentage error , dividing by the exact value.
- [1].
That's the notes covered.
Carry on to the next subtopic.
Try a question
What is the smallest possible value of the actual width of the doorway?
1 mark, marked against the mark scheme
What is the smallest possible value of the actual width of the doorway?
1 mark, marked against the mark scheme