Specific heat capacity and specific latent heat
Studying this course? Keep your progress in one place.
Key facts
- Specific heat capacity : energy to raise 1 kg by 1 K, (J kg⁻¹ K⁻¹).
- Specific latent heat : energy to change the state of 1 kg at constant temperature, (J kg⁻¹).
- Vaporisation has a much larger latent heat than fusion.
- For heating plus a change of state, work in stages and add the energies; electrical energy is .
- Energy lost to the surroundings makes a measured too large.
Specific heat capacity
The energy needed is mass times specific heat capacity times temperature change: .
The specific heat capacity of a substance is the energy needed to raise the temperature of 1 kg by 1 K (or 1 °C), without a change of state. Its unit is J kg⁻¹ K⁻¹.
All three quantities are needed: is per kilogram, so the mass must be included.
- Energy to change temperature
Worked example
0.50 kg of water (c = 4180 J kg⁻¹ K⁻¹) is heated by 15 K. How much energy is needed?
- 1
Use .
- 2
.
How much energy heats 2.0 kg of water by 10 K (c = 4180 J kg⁻¹ K⁻¹)?
Specific latent heat
During a change of state the temperature stays constant, and the energy needed is mass times specific latent heat: .
The specific latent heat is the energy needed to change the state of 1 kg of a substance without a change in temperature. Its unit is J kg⁻¹.
The specific latent heat of fusion is for melting or freezing; that of vaporisation is for boiling or condensing, and is much larger.
- Energy for a change of state
Fusion
- Melting or freezing
- Ice: 3.34 × 10⁵ J kg⁻¹
Vaporisation
- Boiling or condensing
- Water: 2.26 × 10⁶ J kg⁻¹
- Much larger
Worked example
How much energy melts 0.30 kg of ice (L = 3.34 × 10⁵ J kg⁻¹)?
- 1
Use .
- 2
.
How much energy vaporises 0.10 kg of water at 100 °C (L = 2.26 × 10⁶ J kg⁻¹)?
Combining the equations
Work in stages, calculate the energy for each, and add them. Electrical heating supplies .
If no energy is lost, the electrical energy equals the energy used for heating or for the change of state. Energy lost to the surroundings makes the temperature rise smaller than expected.
Efficiency is the useful energy divided by the energy supplied.
- 1
Stage 1
melt at constant temperature: E = Lm
- 2
Stage 2
heat the liquid: E = mcΔθ
- 3
Add
total E = E₁ + E₂
Worked example
How much energy turns 0.20 kg of ice at 0 °C into water at 20 °C? (L = 3.34 × 10⁵ J kg⁻¹, c = 4180 J kg⁻¹ K⁻¹)
- 1
Stage 1, melting at constant temperature: E₁ = Lm = 3.34 × 10⁵ × 0.20 = 6.68 × 10⁴ J.
- 2
Stage 2, heating the water: E₂ = mcΔθ = 0.20 × 4180 × 20 = 1.67 × 10⁴ J.
- 3
Add the stages: E = E₁ + E₂.
A heater of power 150 W runs for 100 s with no energy lost. How much energy does it supply?
Core Practical 13: specific latent heat
Boil water with an electric heater on a balance, find the energy supplied from and the mass boiled off, then .
Boil water in an insulated container on a balance using an electric heater. Measure and for , and the fall in mass over time .
Energy lost to the surroundings makes too large, because less water is vaporised than the supplied energy should give. Lag the container, fit a lid, or repeat at a second power and use the difference between the two runs to cancel the loss.
- 1
Heat
Boil the water with an electric heater in an insulated container
- 2
Measure E
Record V, I and t, so E = VIt
- 3
Measure m
Find the fall in mass on the balance
- 4
Calculate
L = E / m
Why is the measured L too large if energy is lost to the surroundings?
Core Practical 12: thermistor thermostat
An NTC thermistor and a fixed resistor form a potential divider whose output depends on temperature; a calibration graph gives the switching temperature.
An NTC thermistor's resistance falls as its temperature rises. In series with a fixed resistor across a constant supply, it forms a potential divider.
Place the thermistor in a water bath with a thermometer, with a voltmeter across the thermistor. Change the temperature in steps, stirring and waiting for the thermistor to reach the bath temperature. Plot a calibration graph and read off the temperature at the p.d. where the circuit should switch. The fixed resistor sets the switching point.
- P.d. across thermistor
The temperature rises. What happens to the p.d. across an NTC thermistor in this circuit?
Try an exam question
0.050 kg of water at 100 °C is boiled away by a 150 W heater with no energy lost. The specific latent heat of vaporisation of water is 2.26 × 10⁶ J kg⁻¹. Calculate the energy needed and the time taken.
[4 marks]
- [1]Use .
- [1] J.
- [1]Use .
- [1] s.
That's the notes covered.
Carry on to the next subtopic.
Try a question
The temperature of the water rises by 15 K. What is the energy transferred to the water?
1 mark, marked against the mark scheme
The temperature of the water rises by 15 K. What is the energy transferred to the water?
1 mark, marked against the mark scheme